Geotechnical

The resilient modulus can be obtained directly from the repeated load triaxial test in the laboratory and is defined as the ratio of the deviator stress to the recoverable elastic strain after a series of a combination of the confining and deviator stresses applied to a specimen.

• Item Code: IMGT02
• Production Capacity: 100
• Delivery Time: 7-10 days
• Packaging Details: packed in Form fitted rugged carrycase.

The ShearTrac III system is capable of performing the consolidation and shearing phases of a305 x 305 x 205 mm direct shear test under automatic controls for soils and geosynthetics(geomembrane, geotextile, GCL, geogrid, etc.)

• Item Code: IMGT06
• Production Capacity: 100
• Delivery Time: 7-10 days
• Packaging Details: Packed in rugged carry case

The ShearTrac III - DSS is a universal shear system capable of performing the consolidation, static and cyclic direct simple shear phases on large (12 in/ 305 mm) diameter samples under full automatic control. 

• Item Code: IMGT05
• Production Capacity: 100
• Delivery Time: 7-10 days
• Packaging Details: Packed in Rugged Carry case

Table top two pillar Load Frame with high quality machined columns with threading to facilitate movement of crosshead. It comes in capacities of 10, 30, 50 and 100 kN with infinitely variable speed from 0.00001 to 99.99999 mm/min which can be set using the membrane keypad and provision for mounting load cell, LVDT etc.

• Item Code: IMGT12
• Production Capacity: 100
• Delivery Time: 7-10 days
• Packaging Details: Packed in rugged carry case.

AutoLab 2000 is a versatile triaxial apparatus for petrophysical and mechanical rock propertiesmeasurements at in situ conditions on specimens as large as 102 mm (4.0 inches) in diameter. The apparatus is customized based on experimental requirements of the customer.

• Item Code: IMGT14
• Production Capacity: 100
• Delivery Time: 7-10 days
• Packaging Details: Packed in Suitable Carry case.

The Goodman Jack is used for in-situ investigations of the deformability ofrock masses. It is designed to beused in 3" (76 mm) boreholes.

• Item Code: IMFD06
• Production Capacity: 100
• Delivery Time: 7-10 days
• Packaging Details: Packed in carrycase

Cyclic bidirectional direct simple shear enables researchers and geotechnical engineers to subject specimens to cyclic and monotonic loads in two directions. This allows users to simulate the actual 3D loads and displacements acting on the specimens in nature.

• Item Code: IMGT04
• Production Capacity: 100
• Delivery Time: 7-10 days
• Packaging Details: Packed in Suitable carry case

The LoadTrac II / FlowTrac II system fully automates performing a Constant Rate-of-Strain Consolidation (CRS) test. Once a soil sample is in place, and the test conditions selected, this system will run the entire CRS test from start to finish.

• Item Code: IMGT07
• Production Capacity: 100
• Delivery Time: 7-10 days
• Packaging Details: Packed in rugged carrycase

The LoadTrac II / FlowTrac II system provides a unique and versatile way to run permeabilitytests on a wide variety of materials quickly and accurately. This system automates the initialization, saturation, consolidation (isotropic, anisotropic, and Ko) and flow phase by adjusting the gradient or the flow rate across the sample.

• Item Code: IMGT09
• Production Capacity: 100
• Delivery Time: 7-10 days
• Packaging Details: Packed in suitable carry case.

The California Bearing Ratio (CBR) test is used in evalutating subgrade, subbase and base materials as an aid to the design of pavements. The laboratory test uses a circular piston to penetrate material compacted in a mold at a constant rate of penetration.

• Item Code: IMGT11
• Production Capacity: 100
• Delivery Time: 7-10 days
• Packaging Details: Packed in rugged carry case

outine estimations of stiffness have traditionally been made in a stress path triaxial apparatus; however, low-strain testing is difficult due to insufficient resolution and accuracy of load and displacement measuring devices.

• Item Code: IMGT10
• Production Capacity: 100
• Delivery Time: 7-10 days
• Packaging Details: Packed in rugged carry case

The Lab Vane Shear System is used to quickly calculate peak and/or residual undrained shearstrength on intact or remolded specimens in the lab. Once the set-up is in place and the testconditions are selected, the Vane Shear system will run the entire test from start to finish.

• Item Code: IMGT13
• Production Capacity: 100
• Delivery Time: 7-10 days
• Packaging Details: packed in form fitted rugged carry case. Weight of Equipment is 10 kg without carrycase. Dimension of equipment is 394x400x394mm

Core drill machine is also known as diamond core cutting machine or by various other name like pavement core drill, concrete core drill, laboratory core drill machine in accordance to application at various field.

• Item Code: IMGT01
• Production Capacity: 100
• Delivery Time: 7-10 days
• Packaging Details: Packed in rugged carrycase